ACOUSTIC ICP® PRESSURE SENSOR Model 103B01
Acoustic ICP® pressure sensor, 3 psi, 1500 mV/psi, integral 2-wire cable, accel. comp.
- Measurement Range: 3 psi (180.3 dB)
- Sensitivity: (±15%) 1500 mV/psi (217.5 mV/kPa)
- Low Frequency Response: (-5%) 5 Hz
- Resonant Frequency: >=13 kHz (>=13 kHz)
- Electrical Connector: Integral Cable
|
|
ENG |
SI |
|
Performance |
||
|
Measurement Range |
3.00 psi |
180.3 dB |
|
Useful Overrange [3] |
6.00 psi |
186.3 dB |
|
Sensitivity (±15%) |
1500 mV/psi |
217.5 mV/kPa |
|
Maximum Pressure |
250 psi |
1724 kPa |
|
Resolution [2] |
0.02 mpsi |
77 dB |
|
Resonant Frequency |
≥13 kHz |
≥13 kHz |
|
Rise Time |
≤25.0 µ sec |
≤25.0 µ sec |
|
Low Frequency Response (-5 %) |
5 Hz |
5 Hz |
|
Non-Linearity [1] |
≤2.0 % FS |
≤2.0 % FS |
|
Environmental |
||
|
Acceleration Sensitivity [2] |
0.0005 psi/g |
0.0035 kPa/(m/s2) |
|
Temperature Range (Operating) |
-100 to +250 °F |
-73 to +121 °C |
|
Temperature Coefficient of Sensitivity |
≤0.2 %/°F |
≤0.36 %/°C |
|
Maximum Flash Temperature |
1000 °F |
538 °C |
|
Maximum Vibration |
1000 g pk |
9807 m/s² pk |
|
Maximum Shock |
1000 g pk |
9807 m/s² pk |
|
Electrical |
||
|
Discharge Time Constant (at room temp) |
0.1 to 2.0 sec |
0.1 to 2.0 sec |
|
Excitation Voltage |
20 to 30 VDC |
20 to 30 VDC |
|
Constant Current Excitation |
2 to 20 mA |
2 to 20 mA |
|
Output Impedance |
≤100 Ohm |
≤100 Ohm |
|
Output Bias Voltage |
7 to 13 VDC |
7 to 13 VDC |
|
Physical |
||
|
Sensing Element |
Ceramic |
Ceramic |
|
Housing Material |
Stainless Steel |
Stainless Steel |
|
Diaphragm |
316 Stainless Steel |
316 Stainless Steel |
|
Sealing |
Epoxy |
Epoxy |
|
Electrical Connector |
Integral Cable |
Integral Cable |
|
Cable Termination |
Pigtail Ends |
Pigtail Ends |
|
Cable Type |
32 AWG stranded wires |
32 AWG stranded wires |
|
Cable Length |
15 in |
38.1 cm |
* All specifications are at room temperature unless otherwise specified.
Specification Notes
[1] Zero-based, least-squares, straight line method.
[2] Typical.
[3] For +10 volt output, minimum 24 VDC supply voltage required. Negative 10 volt output may be limited by output bias.
[4] See PCB Declaration of Conformance PS023 for details.
Accessories
|
Supplied |
||
|
070B09 |
Solder connector adaptor (10-32 plug to solder terminal, straight pins for both terminals) |
1 |
|
PCS-1 |
Calibration of dynamic pressure sensors at 20% intervals to full scale, max 15 kpsi range. |
0 |
|
PCS-24 |
|
0 |
|
061A04 |
Sleeve clamp, 4-40 cap screw (for Models 103A & 103A11) |
2 |
|
065A66 |
Adhesive mounting ring (for Series 103B) |
3 |
Optional Versions
(M) Metric Mount
|
Accessories: |
|||
|
Supplied |
M061A04 |
Clamp |
2 |