HIGH RESOLUTION ICP® PRESSURE SENSOR Model 112A22
High resolution ICP® pressure probe, 50 psi, 100 mV/psi, 0.218" dia. diaphragm, accel. comp.
- Measurement Range: 50 psi (345 kPa)
- Sensitivity: (±15%) 100 mV/psi (14.5 mV/kPa)
- Low Frequency Response: (-5%) 0.5 Hz
- Resonant Frequency: >=250 kHz (>=250 kHz)
- Electrical Connector: 10-32 Coaxial Jack
- Weight: 0.21 oz (6.0 gm)
|
|
ENG |
SI |
|
Performance |
||
|
Measurement Range |
50.00 psi |
345 кПа |
|
Useful Overrange [3] |
100.00 psi |
690 кПа |
|
Sensitivity (±15%) |
100 mV/psi |
14.5 mV/kPa |
|
Maximum Pressure (step) |
500 psi |
3450 kPa |
|
Maximum Pressure (total) |
15000 psi |
103421 kPa |
|
Resolution [2] |
0.1 mpsi |
0.000689 kPa |
|
Resonant Frequency |
≥250 kHz |
≥250 kHz |
|
Rise Time |
≤2.0 µ sec |
≤2.0 µ sec |
|
Low Frequency Response (-5 %) |
0.5 Hz |
0.5 Hz |
|
Non-Linearity [1] |
≤1.0 % FS |
≤1.0 % FS |
|
Environmental |
||
|
Acceleration Sensitivity [2] |
0.002 psi/g |
0.0014 kPa/(m/s2) |
|
Temperature Range (Operating) |
-100 to +275 °F |
-73 to +135 °C |
|
Temperature Coefficient of Sensitivity |
≤0.03 %/°F |
≤0.054 %/°C |
|
Maximum Flash Temperature |
3000 °F |
1650 °C |
|
Maximum Vibration |
2000 g pk |
19600 m/s² pk |
|
Maximum Shock |
20000 g pk |
196000 m/s² pk |
|
Electrical |
||
|
Output Polarity (Positive Pressure) |
Positive |
Positive |
|
Discharge Time Constant (at room temp) |
≥1.0 sec |
≥1.0 sec |
|
Excitation Voltage |
22 to 30 VDC |
22 to 30 VDC |
|
Constant Current Excitation |
2 to 20 mA |
2 to 20 mA |
|
Output Impedance |
≤100 Ohm |
≤100 Ohm |
|
Output Bias Voltage |
8 to 14 VDC |
8 to 14 VDC |
|
Physical |
||
|
Sensing Geometry |
Compression |
Compression |
|
Sensing Element |
Quartz |
Quartz |
|
Housing Material |
17-4 Stainless Steel |
17-4 Stainless Steel |
|
Diaphragm |
Invar |
Invar |
|
Sealing |
Welded Hermetic |
Welded Hermetic |
|
Electrical Connector |
10-32 Coaxial Jack |
10-32 Coaxial Jack |
|
Weight |
|
6.0 gm |
* All specifications are at room temperature unless otherwise specified.
Specification Notes
[1] Zero-based, least-squares, straight line method.
[2] Typical.
[3] For +10 volt output, minimum 24 VDC supply voltage required. Negative 10 volt output may be limited by output bias.
[4] See PCB Declaration of Conformance PS023 for details.
Accessories
|
Supplied |
||
|
PCS-1AZ |
|
0 |
|
060A03 |
Clamp nut, 5/16-24-2A thd, 1/4" hex, SS (for Series 111, 112 & 113) |
1 |
|
060A05 |
Clamp nut, M7 x 0.75-6G thd (for Series M111, M112 & M113) |
1 |
|
065A05 |
Seal sleeve, sensor recess mount, 0.248" OD x 0.221" ID x 0.240" thk, 17-4 SS (for Series 111A, 112A & 113A) |
1 |
|
065A02 |
Seal ring, sensor flush mount, 0.248" OD x 0.219" ID x 0.015" thk, brass (for Series 111A, 112A & 113A) |
3 |
Optional Versions
(E) Emralon coating
|
|
ENGLISH |
SI |
|
Electrical Isolation |
100000000 Ohm |
|
|
Coating |
Emralon |
|
(J) Ground Isolated
|
|
ENGLISH |
SI |
|
Electrical Isolation |
100000000 Ohm |
|
(S) Stainless Steel Diaphragm
|
|
ENGLISH |
SI |
|
Diaphragm |
316L Stainless Steel |
|
(W) Water Resistant Cable
|
Accessories: |
|||
|
Supplied |
060A03 |
Clamp nut, 5/16-24-2A thd, 1/4" hex, stainless steel |
1 |
(WM) Water Resistant Cable
|
Accessories: |
|||
|
Supplied |
060A05 |
Clamp nut M7 x 0.75-6g thd |
1 |